Waterworks Etoile Flare Concealed Tub Filler Without Handshow Bedienungsanleitung PDF herunterladen

IMPORTANT

To ensure this product is installed properly, you

must read and follow these guidelines.

The owner/user of the tub filler must keep this

information for future reference.

Blocking is mandatory for securing the trim.

This tub filler must be on-site prior to rough in and

allow the installer to visualize the installation and match

the 6" center spread.

Be sure your installation conforms to local codes.

Refer to the specification and assembly drawings

attached. The tub filler is sold partially assembled but

shown fully disassembled for illustrative and service

purposes only.

Check tub measurements to assure the spout projects

far enough into the tub.

Inspect this product to assure you have all parts required

for proper installation.

Use only a strap wrench or protected/smooth-jaw

wrench on any finished surface.

Do NOT use putty during this installation.

Etoile Wall Mounted Flared Spout Tub Filler

ETTU45 (trim) & GUSV90ET(rough)

Installation Guidelines

W A T E R W O R K S

Waterworks is a registered trademark of Waterworks Inc.

09.15.06

ROUGH IN:

Rough in Depth: 1" from center of inlets to surface of

the finished wall.

IMPORTANT: Wood blocking is mandatory for

securing the trim to the wall using the 2 screws (13a)

provided. Make sure there is a 2"x4"(minimum) area of

blocking 3" above the centerline of the rough.

1. Run

" hot and cold supply lines. The spread between

supplies is 6" on center and is NOT adjustable.

2. Install a well supported

" sweat x

" female IPS

adapter onto each supply line.

3. Verify the supplies are secure, level, at the proper

spread of 6" and equal depths.

4. Remove the nuts (1) from the tub filler body inlets then

pull out the inlet adapters (1a,1b).

5. Slide the nut over the inlet adapter and thread them

into the supplies. Use a 10 mm hex wrench to tighten

the adapters.

6. Align the tub filler body onto the supplies making sure

that the o-ring (1b) does not get pinched then tighten

the nuts (1) to secure the tub filler.

7. In preparation of attaching the spout, sweat a piece of

" copper pipe (10) of appropriate lenght onto a

male IPS x

" sweat adapter (9- not included) then

thread it into the tub filler body.

IMPORTANT: The copper pipe must protrude at least

3" beyond the finished wall.

8. Verify the supplies and tub filler body are secure then

turn on the supplies and check for leaks.

These guidelines have been prepared for the professional contractor to aid in the installation of:

ETOILE WALL MOUNTED FLARED SPOUT TUB FILLER (ETTU45 & GUSV90ET)

All dimensions are based on original specification and are subject to change and variation. Please

consult your Design Associate for current specifications.

Finished Wall

1 2 3

Installation Guidelines 1

Inhaltsverzeichnis

Seite 1 - Installation Guidelines

IMPORTANT To ensure this product is installed properly, you must read and follow these guidelines. The owner/user of the tub filler must ke

Seite 2

Etoile Wall Mounted Flared Spout Tub FillerHANDLE INSTALLATION:9. Unthread the 3 screws (14a) that secure the soap dish (14) to the valve trim and re

Seite 3

PARTS TABLEITEM NO. DESCRIPTION QTY.12NUT, INLET232VALVE BODY112132TRIM15214NOTSUPPLIED1616AADAPTER, SPOUT14ASCREWS16B1111312222216CBELL ESCUTCHEON16D

Kommentare zu diesen Handbüchern

Keine Kommentare

Waterworks Etoile Flare Concealed Tub Filler Without Handshow Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Zubehör fürs Wasser Waterworks Etoile Flare Concealed Tub Filler Without Handshow herunter. Waterworks Etoile Flare Concealed Tub Filler Without Handshower and Ebony Lever Handles User Manual Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Zubehör fürs Wasser Waterworks Etoile Flare Concealed Tub Filler Without Handshow